Solid-state-logic X-Logic Series Manual de usuario

X-Rack Owner’s Manual

Page 6X-Rack Owner’s Manual3. X-Rack Installation3.1 Assembling the X-RackThe X-Rack unit is normally shipped either as an empty rack (SSL Part No. 72

Page 73.3 Connection3.3.1 Power ConnectionThe X-Rack unit has an auto-sensing power supply that can operate on 100 – 230V without adjustment.The power

Page 8X-Rack Owner’s Manual4. Operation - Total Recall4.1 OverviewThe Total Recall computer stores all of the switch and rotary controlpositions fo

Page 9X-Rack Installation and Operation4.2.4 Copy/SwapWhile displaying a TR setup pressing and holding a module SEL switchand then pressing a second S

Page 10X-Rack Owner’s Manual4.4 Setup/MIDI Mode4.4.1 OverviewEnter SETUP/MIDI mode by holding down the SETUP/MIDI switchtill the display reads ‘5e’. T

Page 11X-Rack Installation and Operation4.4.2 MIDI (m1)Under this menu it is possible to set the MIDI controls which can control parts of the X-Rack X

Page 12X-Rack Owner’s Manual• The display will show ‘5a’ and both the ‘SAVE’ LED and display flash.• Create an additional MIDI track in your DAW progr

Page 13X-Rack Installation and OperationWhen Remote Mode is set to MIDI (‘m1’), the ‘soft’ controls on the XR622 Master module may be remotelyoperated

4.4.7 Show Version (ve)Select Show Version by turning the D-Pot till the display shows ‘ve’.Press the D-Pot to show the software versionin three blo

Page 15X-Rack Installation and Operation4.5 Software Download and InstallationSoftware to upgrade your X-Rack unit can be downloaded from th

Page 16X-Rack Owner’s Manual6. Go to the Out MIDI Port menu. Select the MIDI OUT port which is connected to your X-Rack:Note that the Macintosh will

Page 17X-Rack Installation and Operation5. Miscellaneous5.1 X-Rack Internal Links and Fuses5.1.1 Fuses (Mains Inlet)The power supply module is interna

Page 18X-Rack Owner’s ManualX-Rack Connector Details (cont.)Mix Bus LinkLocation: Rear PanelConn’ Type: 25-pin ‘D’ Type FemalePinDescription1 Chassis1

Page 19X-Rack Installation and Operation5.3 Physical Specification *Depth: 180mm / 7.2 inches excluding front panel knob(s) and connectors255mm / 10.2

Page 20X-Rack Owner’s ManualNotes

Page A-1X-Rack Mic Amp ModuleA. The Mic Amp ModuleA.1 ConnectionThe rear panel of the module carries the Mic (‘IN’) and Line input (‘LINE’) XLRs along

Page A-2X-Rack Owner’s ManualA.2.3 HF/LF SectionThis section contains simple high and low pass filters as follows:HF (Low Pass): Frequency range 50kHz

Page A-3X-Rack Mic Amp ModuleA.3 Performance SpecificationThe following pages contain audio performance specification figures for the X-Rack Mic Amp m

Page A-4X-Rack Owner’s ManualA.3.4 Instrument Input PerformanceUn-balanced signal applied to Instrument Input and measured at Output. Pad switched out

Page A-5X-Rack Mic Amp ModuleA.4 Calibration InformationThe X-Rack Mic Amp module is factory calibrated and should only need calibration if a potentio

Super-Analogue™ OutboardOwner’s Manual82S6XR010CSolid State LogicS O U N D||V I S I O NSUPERANALOGUEX - R A C K

Page A-6X-Rack Owner’s ManualA.5 Connector DetailsA.6 Physical Specification *Depth: 200mm / 7.9 inches including front panel knobs, excluding connect

Page B-1X-Rack EQ ModuleB. The EQ ModuleB.1 ConnectionThe module input and output gains can be set to operate at a nominal level of either+4dBu or –10

Page B-2X-Rack Owner’s Manual

Page B-3X-Rack EQ ModuleB.3 Performance SpecificationThe following pages contain audio performance specification figures for the X-Rack EQ Module. No

Page B-4X-Rack Owner’s ManualLMF Band controls:Frequency Variable from 200Hz to 2.5kHzGain Variable by > ±20dB‘Q’ Variable from 0.5 to 2.5 (may als

Page B-5X-Rack EQ ModuleB.4 Calibration InformationThe X-Rack EQ module is factory calibrated and should only need calibration if a potentiometer or o

Page B-6X-Rack Owner’s ManualLF EQ - Maximum GainAdjustment: 1. Set LF Gain to maximum and select LF . Set the audio oscillator for80Hz and adjust L

B.5 Connector DetailsB.6 Physical Specification *Depth: 200mm / 7.9 inches including front panel knobs, excluding connectors275mm / 10.9 inches includ

Page B-8X-Rack Owner’s Manual

Page D-1X-Rack Dynamics ModuleD. The Dynamics ModuleD.1 ConnectionThe module input and output gains can be set to operate at a nominal level of either

X-Rack Owner’s ManualAs research and development is a continual process, Solid State Logic reserves the rightto change the features and specifications

Page D-2X-Rack Owner’s ManualFST ATK – Normally, a controlled linear attack time of 1.5ms per 40dB is provided.Press this button to select a fast atta

Page D-3X-Rack Dynamics ModuleD.3 Performance SpecificationThe following pages contain audio performance specification figures for the X-Rack Dynamics

Page D-4X-Rack Owner’s ManualD.3.5 Measurement ConditionsSignal applied to Input, output measured at Output. All pots anti-clockwise and switches ‘out

Page D-5X-Rack Dynamics ModuleD.4.3 Compressor ThresholdAdjustment: 1. Connect the level meter to the Output and set the oscillator level for–28.35dBu

Page D-6X-Rack Owner’s ManualD.5 Connector DetailsD.6 Physical Specification *Depth: 200mm / 7.9 inches including front panel knobs, excluding connect

Page E-1X-Rack Line Return ModuleE. The Line Return ModuleE.1 IntroductionThe X-Rack Line Return module is designed to operate in conjunction with the

Page E-2X-Rack Owner’s Manual

Page E-3X-Rack Line Return ModuleE.4 Performance SpecificationThe following page contains audio performance specification figures for the X-Rack Line

Page E-4X-Rack Owner’s ManualE.5 Calibration InformationThe X-Rack Line Return module is factory calibrated and should only need calibration if a pote

Page E-5X-Rack Line Return ModuleE.6 Connector DetailsNote The Insert Send is a parallel of the Line Input.Insert Send/ReturnLocation: Rear PanelConn’

Page 1Contents1. Introduction 32. Safety Considerations 42.1 Definitions 42.2 Electrical Safety Warning 42.3 Installation 42.4 Graphical Symbols 43. X

Page E-6X-Rack Owner’s ManualE.7 Physical Specification *Depth: 200mm / 7.9 inches including front panel knobs, excluding connectors275mm / 10.9 inche

Page F-1X-Rack Master ModuleF. The Master ModuleF.1 IntroductionUsed in conjunction with the XR623 X-Rack Line Return module, the XR622 X-Rack Master

Page F-2X-Rack Owner’s ManualF.3.2 Monitor SectionThe Monitor Section enables the Mix and Record busses or a stereo external input tobe monitored, the

Page F-3X-Rack Master Module• Use the D-Pot to select ‘le’ (MIDI Remote Learn) and press SAVE to enable learn mode.• Operate any one of the ‘soft’ con

Page F-4X-Rack Owner’s ManualF.4 Performance SpecificationThe following page contains audio performance specification figures for the X-Rack Master mo

Page F-5X-Rack Master ModuleF.5 Calibration InformationThe X-Rack Master module is factory calibrated and should only need calibration if a potentiome

Page F-6X-Rack Owner’s ManualF.6 Connector DetailsHeadphonesLocation: Front PanelConn’ Type: Stereo 1/4" Jack SocketPin DescriptionTip LeftRingSl

Page F-7X-Rack Master ModuleF.7 Physical Specification *Depth: 200mm / 7.9 inches including front panel knobs, excluding connectors275mm / 10.9 inches

Page F-8X-Rack Owner’s Manual

Page 2X-Rack Owner’s ManualSolid State LogicOXFORD • ENGLANDogicXLSUPERANALOGUEX - R A C K SETUP/ MIDI SAVE Push to Select COPY/ DEL TOTAL R

Page 3Introduction1. IntroductionOverviewThe Solid State Logic X-Rack unit has been developed from the successful range of XLogic outboard equipmentan

Page 4X-Rack Owner’s Manual2. Safety considerationsThis section contains definitions and warnings, and practical information to ensure a safe working

Page 5Safety ConsiderationsMains Supply and PhasesSolid State Logic equipment is designed for connection to single phase supplies with the Neutral con