Solid-state-logic 82S6XL020E Manual de usuario Pagina 1

Super Analogue Mic AmpOwner’s Manual

XLogic Mic Amp Owner’s ManualPage 6240120100240230120100240230120100240230100100V120V23 0V24 0V100V Setting(Use for 90-105V)120V Setting(Use for 105-1

3.0 Installation3.1 Voltage SelectionBefore connecting the mains supply ensure that the voltage range selector next to the IEC socket on the rear ofth

VIDEO 1 VIDEO 2REMOTE MIC AMPS 1-4REMOTE MIC AMPS 5-8REMOTE MIC AMPS 9-12REMOTE MIC AMPS 13-16REMOTE MIC AMPS 17-20REMOTE MIC AMPS 21-24REMOTE MI

3.4 Connection to XL 9000 ConsolesRemote mic amp prewiring has been fitted to many, but not all XL 9000 consoles. In many cases only a smallnumber of

REMOTE 1/2REMOTE 5/6REMOTE 7/8REMOTE 3/4Solid State LogicOXFO RD • ENGLANDRJ45-RJ45 (Cat 5) shielded pin to pin cable.SSL Pt.No. 66C673xx where xx is

3.5 Connection to XLogic Mic Amp RemoteThe XLogic Mic Amp Remote (see drawing on page 2) is a 1U panel, approximately 100mm deep. Each unit willcontro

XLogic Mic Amp Owner’s ManualPage 12ChannelLK5BCD SwitchFront Panel Displays Address *Position SettingDisplay 1Display 2Display 3Display 400000a0DPDPD

3.6 Configuring the XLogic Mic AmpThere are a number of internal link settings, most of which should not normally require adjustment – seeAppendix A f

XLogic Mic Amp Owner’s ManualPage 14+48VPHANTOMPOWER+48V-20dBHi-ZMICTRIM+18 — +78dBMONØ+-25wD25wDMON IN/MON OUTHeadphone ampStereo JackDC Control from

4.0 OperationThe XLogic Mic Amp is a 1U rack mounting unit containing four ultra high quality microphone amplifiers,utilising Solid State Logic’s Supe

XLogic Mic Amp Owner’s ManualPage 16ChannelLK5 (bit 5)BCD SwitchFront Panel Displays Address *PositionSettingDisplay 1Display 2Display 3Display 4xxxx

Appendix A – Internal links and fusesFuses (Mains Inlet)The mains inlet contains a single 1 amp 1.25" time delay fuse (SSL Part No. 35FJJ310). To

XLogic Mic Amp Owner’s ManualPage 18Appendix B: Connector PinoutsMic InputLocation:Front PanelConn' Type:XLR Female PinDescription1Chassis2A

AppendixPage 19Appendix B: Connector Pinouts (continued)Remote 1 - 2Location:Rear PanelConn' Type:8-way RJ45 SocketPinDescription1Ch2Switch Contr

XLogic Mic Amp Owner’s ManualPage 20Appendix B: Connector Pinouts (continued)Table 3a - XL 9000 DL to 25way ‘D’ Wiring: Channels 1-8 / 25-32 / 49-56 /

AppendixPage 21Appendix B: Connector Pinouts (continued)Table 3b - XL 9000 DL to 25way ‘D’ Wiring: Channels 9-16 / 33-40 / 57-64 / 81-88SignalCable #C

XLogic Mic Amp Owner’s ManualPage 22Appendix B: Connector Pinouts (continued)Table 3c - XL 9000 DL to 25way ‘D’ Wiring: Channels 17-24 / 41-48 / 65-72

AppendixPage 23Appendix B: Connector Pinouts (continued)Table 4 - Channel Address Bit LinkingChannelActionChannelActionChannels1-4connectpin11Channels

Appendix C – Performance SpecificationConditions:Source impedance 150Ω unless otherwise stated.All measurements are RMS and are made using a 22Hz to 2

THD + NoiseIn all cases THD is essentially unmeasurable, being less than the inherent noise of the amplifier until the outputlevel exceeds +20dBu.Note

Solid State LogicSuper-Analogue™ OutboardOwner’s Manual82S6XL020ES U P E R A N A L O G U EM I C A M P

Appendix D – Calibration InformationThe XLogic Mic Amp is factory calibrated and should only need calibration if a potentiometer or othercomponent has

Appendix E – Physical Specification *Depth: 325mm/12.8 inches not including heatsink365mm/14.3 inches including heatsink400mm/15.75 inches including c

XLogic Mic Amp Owner’s ManualPage 28

XLogic Mic Amp Owner’s ManualAs research and development is a continual process, Solid State Logic reserves the rightto change the features and specif

Page 1Contents1.0 Introduction 32.0 Safety Considerations 4Safety Warnings 43.0 Installation 7Setting the mains voltage selector 7Mounting 7Standalone

XLogic Mic Amp Remote (front)XLogic Mic Amp Remote (rear)XLogic Mic Amp (rear)XLogic Mic Amp (front)XLogic Mic Amp Owner’s ManualPage 2XLSUPER ANALOG

1.0 IntroductionThe XLogic Mic Amp is a 1U rack mounting unit containing four ultra high quality microphone amplifiers,utilising SSL’s Super Analogue

2.0 Safety considerationsThis section contains definitions and warnings, and practical information to ensure a safe working environment.Please take ti

Mains Supply and PhasesSolid State Logic equipment is designed for connection to single phase supplies with the Neutral conductor atearth potential -